Totaline thermostat manual p374

Posted on 19.01.2021 Comments

Totaline manufactures battery-powered digital thermostats as well as wired battery backup models. You should change the batteries in any Totaline digital thermostat as soon as you see a low battery alert on the screen.

Totaline also recommends battery replacement at least once a year before the start of cold weather to reduce the risk of frozen pipes or other harm caused by low-battery thermostat shutdown.

To access the batteries, you will either remove a front panel from the unit or pull the entire unit from the wall. Typically, you can access and change the batteries in about 10 minutes. Look for two slots on top of your Totaline battery-powered digital thermostat, and then find a slotted screwdriver with a head slightly smaller than the slots.

Stand directly in front of the unit, and insert the head of the screwdriver into a slot. Turn the screwdriver blade 90 degrees toward the front of the unit to unsnap the top of the front panel, and pull that side away from the back of the unit. Insert a slotted screwdriver into the second slot and repeat the process to unsnap the other side. Lift the panel up to remove it from the unit, and then set it to the side.

Check the direction of the positive and negative terminals of the batteries, and then pull and dispose of the old batteries. Insert your new AA batteries with the positive and negative ends matching the alignment of the batteries you pulled.

When finished, slide the bottom of the panel into the bottom of the back of the unit. Push the top against the back until the panel snaps into place. To prevent loss of the date and time in some units, insert the new batteries within two minutes of pulling the old ones. Pull the unit toward you gently to unlock it from the wall plate.

If you have difficulty, try pulling the thermostat away from the bottom and then the top.

TOTALINE P374-1800 Installation Instructions Manual

Turn your thermostat over to the back. Locate the batteries. Check the battery type and the direction of the positive and negative terminals, and then remove the batteries. Set the batteries aside for disposal. Insert fresh batteries with the batteries aligned in the same way as the previous ones. When finished, reattach the unit to the wall plate. Always change the batteries before leaving for a month or longer to try to prevent low-battery thermostat malfunction while you're away.

Based in Southern Pennsylvania, Irene A. Blake has been writing on a wide range of topics for over a decade. Hunker may earn compensation through affiliate links in this story.

totaline thermostat manual p374

It's easy to change the batteries in your Totaline thermostat. Step 1. Step 2.Quick Links. See also: Instruction and Installation Manual. Table of Contents. Digital thermostat 3 heat - 2 cool multi-stage programmable 11 pages.

Heat cool and heat pump dual fuel capable 7-day programmable thermostat pages. Page 2 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.

The first page of each section contains a more detailed Contents of each section, such as the example page shown below. HEAT - Indicates the heating mode. AuxHeat icon Page 3. Follow the step below. For more information on this see page The display will then show the current outside temperature along with the High and Low temperatures for the day.

The display will then show the current indoor humidity along with the humidification setpoint Section 9. This delay may be set for 30, 60, or 90 seconds. If the Fan Off Delay is set for zero seconds, the fan will not energize after a call for cooling has been satisfied. The icon will appear on the display, then release the buttons. Page 42 HUM as shown in Figure 1 below.

This will allow you to access the humidification and dehumidification setup steps. For proper humidity operation, this jumper must be set for HUM. When the thermostat detects the humidity percentage is above the setpoint for This counter keeps track of the number of days since the Service Humidify icon was reset.

This counter keeps track of the number of days since the UV light icon was last reset. Since most gas furnaces control the fan, this feature should be off unless the heater is only electric. This minimum difference is enforced during Auto-Changeover operation. Press the MODE button.Quick Links. Table of Contents. Digital thermostat 3 heat - 2 cool multi-stage programmable 11 pages. Heat cool and heat pump 7-day programmable digital thermostat 24 pages.

Heat cool and heat pump dual fuel capable 7-day programmable thermostat pages. Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.

If you are unsure about any of these steps, call a qualified technician for assistance. If it does not come off easily check for screws. Loosen the screws holding the thermostat base or subbase to the wall, and lift away. Wire from the Install on the Press the Up or Down buttons until the set temperature is 10 degrees above room temperature.

If calibration is required, please contact a trained HVAC technician to correctly perform the following procedure. CAUSE: The compressor timer lockout may prevent the air conditioner from turning on, for a period of time. See pages 5.

This manual is also suitable for: P Print page 1 Print document 17 pages. Cancel Delete. Sign In OR. Don't have an account?

Sign up! Restore password. Upload from disk. Upload from URL.Quick Links. See also: Owner's Manual. Table of Contents. Digital thermostat 3 heat - 2 cool multi-stage programmable 11 pages. Heat cool and heat pump dual fuel capable 7-day programmable thermostat pages.

Page 2 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation. If you are unsure about any of these steps, call a qualified technician for assistance. If it does not come off easily check for screws.

Loosen the screws holding the thermostat base or subbase to the wall, and lift away. These outputs are designed to have different functions depending on how the jumpers are set below.

totaline thermostat manual p374

Wire from the Install on the Press the Up or Down buttons until the set temperature is 10 degrees above room temperature. If calibration is required, please contact a trained HVAC technician to correctly perform the following procedure.

CAUSE: The compressor timer lockout may prevent the air conditioner from turning on, for a period of time. See pages 5. Print page 1 Print document 24 pages.

Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.Totaline thermostat troubleshooting table allowing to reveal malfunctions of a device in time and conduct repair work is given below. Everything is stated in simple and understandable even for an ordinary user language. When the temperature limit is exceeded, the furnace shuts off the burners and the 24VAC to the thermostat.

When the stat loses power, the clock stops. The furnace blower remains on, so the homeowner may never notice a problem, and when the temperature is back within limits, the burners come back on, and the power to the stat is restored.

The clock will be slow by however many minutes the power was off to the thermostat. Correction: Find the cause of the high temperatures - dirty filter, etc. If the common wire is present, check it for continuity, look for a short, a broken wire, or a bad connection. If the equipment is a heat pump, or heat only or cool only, you MUST have a common wire.

Unit running backwards Cooling on heat demand, heating on cool demand - the heat pump setting is wrong - go to setup step 3 and change the heat pump setting. If the unit is a commercial heat pump, it may not require a heat pump thermostat, so step 3 should be turned OFF. In this case, electric heat setup step 5 may have to be turned ON. Display goes blank during heating Most likely the furnace is tripping on high limit or some other safety limit.

The furnace will shut off the burners AND break the R leg to the thermostat, so the thermostat has no power and will go blank.

Solution - identify the cause of the limit trips. They must match. The house code on the receiver is set using dip switches, the house code on the thermostat is set in the thermostat setup, step 4. Check setup step 3 zoningit should be always be set to no.

Also, check batteries - these thermostats require AA Lithium batteries, alkalines will not work correctly. Batteries die rapidly in wireless stat Make sure the batteries are AA Lithium batteries. Regular alkaline batteries will die rapidly and cause erratic thermostat operation.

Valley Mechanical Venstar T2900SCH

Also check the thermostat backlight setting in setup step 9. If the backlight is ON, the batteries will run down very rapidly. If the customer really wants the backlight on all the time, use the optional transformer part P to plug the thermostat into a wall outlet. If you only hold the buttons two seconds, you can only get to step two.

Press Mode, Up and Down simultaneously to unlock the buttons.

totaline thermostat manual p374

Temperature inaccurate Calibrate the thermostat. On 4 button models, press Mode and Down for two seconds, the whole display will light up. Press Mode, and the room temperature will appear. Use the Up or Down buttons to adjust the temperature. Press Mode to exit.These instructions provide simple and short troubleshooting guidelines for the most popular Totaline thermostat models.

In each manual, you will find the list of the most widespread technical malfunctions, possible causes and the ways to fix the issues. Problem Solution Display is blank Check circuit breaker and reset if necessary. Make sure furnace door is closed securely.

Make sure the temperature is set higher than the Inside temperature. Make sure the temperature is set lower than the Inside temperature. Check circuit breaker and reset if necessary. Wait 5 minutes for the system to respond. Check sensor for damage. If recessing power does not clear display, thermostat should be replaced.

Double check wiring and check for 24 vac between R and C. E2 will clear 15 seconds after proper voltage is restored.

This is to remind the homeowner to check the filter. Press the Reset Filter button to clear display and reset timer to 0.

Decrease the cooling setpoint to 10 degrees below room temperature. Simultaneously press the Up Arrow and Fan buttons together increase temperature. If present, the thermostat is OK and the problem is with equipment or wiring. If not present, replace the thermostat. Increase the heating setpoint to 10 degrees above room tem- perature. Problem Solution Screen is blank. Ensure the furnace door is properly closed.

Ensure two fresh AAA alkaline batteries are correctly installed. Temperature settings cannot be changed. The System switch is off. Cool or Heat A is flashing. The compressor protection delay has been activated. Wait for the delay to end maximum of 5 minutes.

HI appears on the screen. LO appears on the screen. E1 appears on the screen. The temperature sensor circuit is opened. Replace the thermostat. E2 appears on the screen. If thermostat is battery powered, make sure fresh AAA alkaline batteries are correctly installed No response to key presses or temperature will not change Check to make sure the thermostat is not locked Make sure heating and cooling temperatures are set to acceptable range Backlight is dim If thermostat is battery powered, make sure fresh AAA alkaline batteries are correctly installed If thermostat is AC powered, a dim display is normal.

The backlight remains on at a low level, and brightens when a key is pressed. Auto indicates the thermostat is following the programmed fan setting.Of note, cornerback Desmond Trufant suffered a concussion and will not play.

totaline thermostat manual p374

Fellow corner Brian Poole only turned in one limited practice this week and is questionable. Against the superior tag-team duo of Adam Thielen and Stefon Diggs, the Falcons need all hands on deck to hang with the fantastic Viking pass attack.

Without Trufant (and maybe Poole), it could be a long day for the Atlanta defense. The New England Patriots can win this game however they want. If they prefer to go to the ground and give the ball to running backs Dion Lewis and Rex Burkhead close to 40 times, they'll be successful. If they want to go long to deep threat Brandin Cooks, they should be fine. If they want to feed tight end Rob Gronkowski in his annual homecoming game in Western New York, they can do that, too.

That's less of an indictment on the Buffalo defense, which has been up and down (sometimes very down) all year but has overall surpassed low preseason expectations. Rather, it's a commentary on the fact that the Pats are firing on all cylinders after winning seven straight.

The guess here is that this game becomes an "anything you can do, I can do better" matchup between the Carolina Panthers' No. When these two teams played in September, Thomas had five catches for 50 yards and one touchdown on the first drive alone. He didn't see many targets the rest of the way as the Saints were largely in command of the matchup and went to the ground, but Thomas showed he can beat the Panthers secondary.

As for Funchess, he is facing a Saints team that is missing safety Marcus Williams and may not have cornerback Marshon Lattimore, who is questionable with an ankle injury. Ken Crawley is back from an abdomen injury, but as he told Josh Katzenstein of NOLA. Philadelphia Eagles at Seattle SeahawksIf the Seattle offensive line can hold off the Philadelphia Eagles' front seven long enough for quarterback Russell Wilson to do work, then the 'Hawks can protect their house and pull off the upset.

TOTALINE P374-1800 Owner's Manual

If the Seahawks falter in that regard, then it could be a long day for the Seattle offense. The other issue is the Seattle running game, which simply hasn't been able to get going this year. According to Football Outsiders, Seattle ranks just 28th in the league in adjusted line yards. The problem is the Eagles' defensive line is ranked first by a long shot in that category.

Ultimately, the Eagles' front seven seems to have a big edge over the Seattle front, and that should be the difference. Pittsburgh Steelers at Cincinnati BengalsIt seems like the Pittsburgh Steelers and Cincinnati Bengals engage in knockdown, drag-'em-out games against each other when they face off.

Such is the reputation of the AFC North. Don't expect many offensive fireworks in this contest. Both defenses are stout and capable of shutting down the opposing offenses. The Bengals' attack has been hit or miss all season, although they showed signs of life on the ground thanks to rookie Joe Mixon's best day as a professional.

Green is still a problem for any team he faces, and tight end Tyler Kroft has done well in Tyler Eifert's stead. Although the Bengals are at home and the more desperate team as they sit one game out of the playoffs, it's hard to bet against Pittsburgh, who has won six straight and has been lights out on both sides of the ball. Even if wideout Antonio Brown doesn't go (he didn't practice on Saturday and is questionable, per Jeremy Fowler of ESPN.

Their exploits should lead to a close Steeler win. But now it gets even trickier and Joe Root and co as they look to complete the hardest task of all: winning the Ashes in Australia. According to Oddschecker on November 15. Lads, these games last five days. Away from home they will have to be a strong, tight-knit group and will need big leaders.

Enter Ben Stokes and Alastair Cook. Simon Heffer Premium 07 Dec 2017, 2:39pm Comment: England should fear a 5-0 - Australia have not even played their best yet Mitchell Johnson Premium 07 Dec 2017, 10:17am Who will win the 2017 Ashes. Our Ashes-ometer on whether Australia or England are on track for success 07 Dec 2017, 10:17am Can England avoid another Ashes whitewash Down Under.